Give Push to your Success with Dell Hyperconverged Infrastructure D-VXR-DY-01 Exam Questions
D-VXR-DY-01 100% Guarantee Download D-VXR-DY-01 Exam PDF Q&A
NEW QUESTION # 150
An implementation engineer is deploying a new VxRail cluster.
What should they confirm before installing the hardware?
- A. Service laptop is on the same IP network as the iDRACs
- B. Power distribution supports only the power rating of a single node
- C. Redundant power zones exist with adequate power cables
- D. At least 24 in (61 cm) of clearance must exist in front of and behind the cabinet
Answer: D
NEW QUESTION # 151
What categories can be validated by the VxRail NVT?
- A. Network Services, ToR Switches, and Upstream Switches
- B. Network Services, ToR Switches, and VxRail Nodes
- C. Network Services, Upstream Switches, and VxRail Nodes
- D. ToR Switches, Upstream Switches, and VxRail Nodes
Answer: A
NEW QUESTION # 152
An implementation engineer is in the validation phase of a VxRail deployment with two Dell EMC ToR switches.
Which command should they run on each of the ToR switches to validate that Link Aggregation has been configured according to Dell best practices for VxRail node interfaces?
- A. show network-policy profile
- B. show port-channel summary
- C. show interface status
- D. show interface
Answer: B
NEW QUESTION # 153
You are configuring a VxRail to connect to an existing, external SRS VE. The customer's support account is associated with the Site ID/Party ID where VxRail is installed. A validation error is issued when you attempt to register VxRail in SRS.
What is the possible cause for the error?
- A. SRS traffic goes through a proxy server
- B. Status of VxRail in Install Base is Shipped
- C. Wrong IP address was used for SRS VE gateway
- D. Number of deployed devices on SRS gateway has exceeded the maximum
Answer: B
NEW QUESTION # 154
What is the correct order of steps to install a Dell PowerEdge-based VxRail cluster?
Answer:
Explanation:
NEW QUESTION # 155
A VxRail cluster is being deployed with the VxRail Deployment Wizard.
For which IP addresses must FQDNs be resolved by DNS?
- A. All VxRail ESXi nodes, vRealize Operation Manager, and VxRail Manager VM
- B. Only the first VxRail ESXi node, vCenter Server, and VxRail Manager VM
- C. All VxRail ESXi nodes, vCenter Server, and VxRail Manager VM
- D. vCenter Server and VxRail Manager VM only
Answer: C
NEW QUESTION # 156
What is the default IP address of the VxRail Manager?
- A. 192.168.1.16
- B. 192.168.10.200
- C. 192.168.1.200
- D. 192.168.10.16
Answer: B
NEW QUESTION # 157
What is validated by running the Proactive VM Creation test in vCenter on a VxRail cluster?
- A. vSAN operates successfully
- B. Network performance is sufficient
- C. Network firewalls are configured correctly
- D. vSAN has sufficient storage capacity
Answer: A
NEW QUESTION # 158
What is configured by default during the initial deployment of a VxRail cluster with All-Flash nodes?
- A. vSAN Performance Service
- B. AID-1 vSAN storage policy
- C. RAID-5 vSAN storage policy
- D. vSAN Deduplication and compression
Answer: B
NEW QUESTION # 159
What is the base URL for the VxRail API call?
- A. http://<VxM_IP>/vxm/v1/
- B. https://<VxM_IP>/API/vxm/v1/
- C. https://<VCenter_IP>/rest/vxm/v1/
- D. https://<VxM_IP>/rest/vxm/v1/
Answer: D
NEW QUESTION # 160
What is a benefit of programmatically gathering VxRail information with a REST API call?
- A. Perform Day 2 vSAN configuration changes
- B. Perform node shutdowns and specific operations
- C. Obtain status of all running operations on a cluster
- D. Automate iDRAC firmware management and status
Answer: C
NEW QUESTION # 161
What is a requirement for Top of Rack (ToR) switch VxRail node ports?
- A. Enable IGMP Querier
- B. Disable IGMP Snooping
- C. Enable Spanning Tree
- D. Disable Link Aggregation
Answer: D
NEW QUESTION # 162
A planned VxRail Stretched Cluster will have four All-Flash nodes at each site
What is the recommended storage policy to ensure cross-site and local protection, using storage as efficiently as possible?
- A. Site disaster tolerance - None - keep data on Preferred (stretched cluster) Failures to tolerate - 1 failure - RAID-5 (Erasure Coding)
- B. Site disaster tolerance - Dual site mirroring (stretched cluster) Failures to tolerate - 1 failure - RAID-5 (Erasure Coding)
- C. Site disaster tolerance - Dual site mirroring (stretched cluster) Failures to tolerate - 1 failure - RAID-1 (Mirroring)
- D. Site disaster tolerance - Dual site mirroring (stretched cluster) Failures to tolerate - no data redundancy
Answer: B
NEW QUESTION # 163
What is the size of the drives on the BOSS card in a VxRail P570 node?
- A. 240 GB
- B. 256 GB
- C. 64 GB
- D. 120 GB
Answer: A
NEW QUESTION # 164
What is the correct command to restart the Loudmouth process on a VxRail node?
- A. /usr/lib/vmware-loudmouth/bin/loudmouthc restart
- B. /sbin/service loudmouth restart
- C. systemctl restart vmware-loudmouth
- D. /etc/init.d/loudmouth restart
Answer: D
NEW QUESTION # 165
How many nodes can be added simultaneously to an existing VxRail cluster running at code version 4.5?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 166
An implementation engineer logs in to the vSphere Client of a recently deployed VxRail cluster. They want to review the firmware versions on the VxRail nodes.
Which view should they use to gather this information?
- A. Hosts and Clusters > VxRail Cluster > Configure > VxRail > System
- B. Hosts and Clusters > VxRail Cluster > Monitor > VxRail > Appliances
- C. Hosts and Clusters > VxRail Host > Configure > VxRail > iDRAC Configuration
- D. Host and Clusters > VxRail Host > Monitor > VxRail > Physical View
Answer: D
NEW QUESTION # 167
How can an administrator limit IPv6 traffic created by VxRail nodes?
- A. Create a unique VLAN for IPv6 traffic
- B. Configure Link Aggregation
- C. Tag VLAN 3939 on the ToR switches
- D. Enable MLD snooping and querier
Answer: D
NEW QUESTION # 168
What is the maximum number of hosts supported in a VxRail Stretched Cluster?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 169
A customer has decided that they will be using the Spanning Tree protocol in their Dell EMC ToR switches.
How should the switch ports used for VxRail be configured to achieve a successful deployment?
- A. Set the port type to edge
- B. Set the port mode to access
- C. Enable MLD snooping and querier
- D. Enable link aggregation for all ports
Answer: A
NEW QUESTION # 170
What network setting is the optional configuration on the port group for a customer-supplied VDS before the VxRail cluster is deployed?
- A. Configure NIC teaming and failover
- B. Enable NIC teaming and failover
- C. Assign NIC uplinks
- D. Enable and configure NIOC
Answer: D
NEW QUESTION # 171
What guideline should be followed when planning bandwidth between sites hosting VM objects and the witness nodes?
- A. 2 Mbps for every 1000 objects on the vSAN
- B. 500 ms roundtrip (< 250 ms one way)
- C. 5 ms with a recommended minimum bandwidth of 10Gbps
- D. 1500 MTU on the VSAN vmkernel interface
Answer: A
NEW QUESTION # 172
Dell EMC will be responsible for the configuration of ToR and Management switches for a VxRail deployment.
Where should these details be documented?
- A. Dell EMC Fabric Design Center
- B. Dell EMC VxRail Configuration Portal
- C. VxRail Appliance PEQ
- D. VxRail Network PEQ
Answer: D
NEW QUESTION # 173
What is required to configure SRS for VxRail?
- A. VMware ELA
- B. VxRail Node Imaging Management Tool
- C. Log Insight
- D. Dell EMC Support Account
Answer: D
NEW QUESTION # 174
How should an administrator manually validate the DNS readiness of a customer network?
- A. Ping the default gateway of the management VLAN
- B. Generate a Network PEQ
- C. Run a traceroute to the DNS server
- D. Run nslookup on server FQDN and IP
Answer: D
NEW QUESTION # 175
......
Get D-VXR-DY-01 Actual Free Exam Q&As to Prepare Certification: https://testking.testpassed.com/D-VXR-DY-01-pass-rate.html